Variation of dayside chorus waves associated with solar wind dynamic pressure based on MMS observations

The whistler-mode chorus waves are one of the most important plasma waves in the Earth’s magnetosphere. Generally, the amplitude of whistler-mode chorus waves prefers to strengthen when the energetic fluxes of anisotropic electrons increase outside the plasmapause. This characteristic is commonly associated with the geomagnetic storms or substorms. However, the relationship between the solar wind dynamic pressure (P_sw) and the long-time variation of chorus waves during the quiet period of the geomagnetic activity still needs more detailed investigations. In this paper, based on MMS observations, we present a chorus event just observed in the inner side of magnetopause without obvious geomagnetic storms or substroms. Interestingly, during this time interval, some P_sw fluctuations were recorded. Both the amplitudes and frequencies of chorus waves changed as a response to the variation in P_sw. It proved that the enhancement of P_sw increases the energetic electrons fluxes, which provides free energies for the chorus amplification. Furthermore, the wave growth rates calculated using linear theory increases and the central frequency of the chorus waves shifts to a higher frequency when the P_sw enhancement is greater, which are also consistent well with the observations. The results provide a direct evidence that the P_sw play an important role in the long-time variation of whistler-mode chorus waves inside the magnetopause.     

1 500℃极端高温环境下高超声速飞行器轻质隔热材料热/振联合试验

远程高超声速飞行器处于极为恶劣的气动加热与振动耦合环境中,长时间的高温与振动载荷相互叠加会导致飞行器热防护材料出现裂纹、错位、剥离或脱落,甚至会引发致命的安全事故。因此热防护材料在极端高温环境下的地面热/振联合试验测试,对于高超声速飞行器的安全可靠性设计极为重要。建立高温与振动复合试验环境,设法解决轻质多孔隔热材料在强振动下,表面温度难于准确测量与控制的难题,制作水冷式隔热装置保护价格昂贵的振动激励设备等,实现了1 500℃高温环境下高超声速飞行器轻质隔热材料的热/振联合试验。得到非金属隔热材料陶瓷纤维板内部的断裂形貌及裂纹断面特征。根据试验前、后材料的表观及微观变化以及内部结合剂的变化等试验结果,对材料进行改进。经过试验测试后,达到了使用要求。本文建立的1 500℃极端高温环境下的热/振联合试验系统及试验结果为远程高超声速飞行器热防护材料的抗振动能力评估、隔热效果确定以及材料性能的改进提供了重要支撑。     

0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

民用涡轴发动机进气系统结冰试验

围绕中国民航规章CCAR-33部R2版中第33.68条款适航要求,针对涡轴发动机提出了一种满足适航要求的试验方法,包括结冰关键点分析、结冰取证试验点选定、整机结冰取证试验三部分。结合涡轴发动机工作包线,开展结冰关键点分析以选定结冰取证试验点。在结冰包线内选择了若干结冰计算点,并计算每个点的结冰位置与结冰量。计算结果显示:温度接近0 ℃且海拔高度较低的区域是涡轴发动机结冰量显著的区域。结冰试验时在-4~-1 ℃的温度区间寻找刚出现结冰的温度点与结冰量最大的温度点。试验结果显示:结冰量最大的温度点是最严酷的结冰试验点。     

基于实战使用的涡轴发动机空中起动飞行试验

以涡轴发动机实战使用中空中紧急起动相关技术指标和特情处置措施验证为目的,设计了贴近实战使用特征的发动机空中起动试飞方案,并以某涡轴发动机设计定型试飞为依托,进行了不同飞行工况下的飞行试验验证和数据分析研究。结果表明:该空中起动试飞方案合理可行,能够最大程度的贴近部队实战使用的技术特征,满足对发动机起动高度包线、起动时间等研制总要求规定的技术指标验证需求;试飞结果表明该型涡轴发动机4000m以上高度停车至再起动期间直升机平均下滑高度约为670m,平均停车时间约为185s。该试飞方法和数据结果可为部队实战使用过程中空中遭遇停车的紧急处置提供支持和参考。     

航空发动机低压转子系统的动力学相似设计方法

提出了航空发动机转子系统动力学相似设计方法,以便采用模型替代实际结构对其动力学特性进行研究。基于转子系统的动力学等效原则,通过动力学优化方法建立全尺寸原型的相似等效模型。综合采用方程分析和量纲分析推导转子系统的动力学相似准则,并根据转子设计参数的相似关系建立相似等效模型的缩比模型。基于模型修正方法对三维设计模型的相似误差进行修正,得到预测精度较高的动力学相似模型。以双转子发动机低压转子试验模型的动力学相似设计为例,通过有限元仿真对动力学相似设计方法的有效性进行了验证。结果表明:在设计转速范围内,通过该方法得到的动力学相似模型能够有效预测全尺寸原型的临界转速和不平衡响应,前三阶临界转速的相似误差分别为3.09%、1.75%和0.31%,对应振型的相关性均大于0.93。该方法具有较高的实用价值,可为发动机整机动力学相似设计提供参考。     

基于激光多普勒原理的极低风速测量实验

介绍了利用激光多普勒效应进行风速测量的原理及定点遥测原理,分析了探测气溶胶颗粒大小的要求,并以此搭建了一套极低风速测量系统。同时分析了系统的测速精度,以及安装角度对测量结果的影响。最后分别开展了转台实验、直线导轨实验和风洞实验,实验结果表明,该极低风速测量系统的测量误差基本可以控制在001 m/s以内,当风洞工作介质为未经处理的环境空气时,系统可以获得稳定可靠的信号,测量结果与高性能仪器十分接近。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

大型飞机迎角保护控制律设计及试飞技术研究

针对大型飞机迎角保护控制律设计及试飞问题,通过杆位移-过载梯度的实时精确调整及取大值逻辑指令切换,设计了迎角保护控制律,实现拉杆到底飞机迎角达到且不超过限制迎角的目的。根据迎角保护控制律的功能及试飞目的,将整个试飞过程分为三个阶段,研究了各个阶段的试飞技术。仿真结果表明,所设计的控制律能够实现迎角保护功能,具有良好的控制效果。